微通道板表面羟基化工艺研究北大核心

研究了3种微通道板基底羟基化的方法,测量了羟基化处理后微通道板基底表面水接触角及通道端面的形貌变化,分析了各种方法中微通道板基底的亲水性和腐蚀情况。实验结果表明:氨水双氧水溶液对基体表面的亲水性能提升不大,NaOH溶液对基体有腐蚀作用,经食人鱼溶液处理的基体表面亲水性明显提高且无腐蚀作用。研究了微通道板在食人鱼溶液中的浸泡时间和浸泡温度对表面亲水性的影响。结果表明:随着浸泡温度的增加,微通道板表面水接触角先减小后增大,当温度为80℃时达到极小值,浸泡时间对微通道板表面的亲水性影响不大。最终确定了微通道板表面羟基化工艺:浸泡温度为80℃,静置时间为20~60 min。     

Experimental study on uplift behavior of shallow anchor plates in geogrid-reinforced soil

Geogrid reinforcement can significantly improve the uplift bearing capacity of anchor plates. However, the failure mechanism of anchor plates in reinforced soil and the contribution of geogrids need further investigation. This paper presents an experimental study on the anchor uplift behavior in geogrid-reinforced soil using particle image velocimetry (PIV) and the high-resolution optical frequency domain reflectometry (OFDR). A series of model tests were performed to identify the relationship between the failure mechanism and various factors, such as anchor embedment ratio, number of geogrid layers, and their location. The test results indicate that soil deformation and the uplift resistance of anchor plates are substantially influenced by anchor embedment ratio and location of geogrids, whereas the number of geogrid layers has limited influence. In reinforced soil, increasing the embedment ratio greatly improves the ultimate bearing capacities of anchor plates and affects the interlock between the soil and geogrids. As the embedment depth increases, the failure surfaces gradually change from a vertical slip surface to a bulb-shaped surface that is limited within the soil. The strain monitoring data shows that the deformations of geogrids are symmetrical, and the peak strains of geogrids can characterize the reinforcing effects.     

行李箱外板浮动整形模设计

介绍了某轿车行李箱外板的翻边侧整形模设计过程,行李箱外板的侧法兰翻边上存在凹包,其翻边方向和凹包成形方向不同,常规需要2道工序分别完成翻边和凹包成形。该模具突破了传统的设计结构,在翻边机构中设置了凹包成形机构,将2个不同方向的成形复合到1道工序中,减少了模具数量,降低了冲压成本和工装成本。     

Cold sintered,temperature-stable CaSnSiO5-K2MoO4 composite microwave ceramics and its prototype microstrip patch antenna

Dense (1-x)wt%CaSnSiO₅-xwt%K₂MoO₄ (CSSO-KMO) composite ceramics were fabricated by the cold sintering process at 180 °C under 400 MPa for 60 min. X-ray diffraction, Energy dispersive X-ray and Raman spectroscopy confirmed that CSSO and KMO coexisted without intermediate phases. As KMO weight fraction increased, relative permittivity (ε_r) and temperature coefficient of resonant frequency (τ_f) decreased and the microwave quality factor (Q×f, where f is resonant frequency) increased. Near-zero τ_f (-0.5 ppm/°C) was obtained for 65 wt%CSSO-35 wt%KMO with ε_r ～ 9.2 and Q×f ～ 6240 GHz. No chemical reaction between ceramic composites and silver was observed, demonstrating potential for cofiring with Ag-paste. A prototype antenna was fabricated from 65 wt%CSSO-35 wt%KMO composite ceramic with a bandwidth of 144 MHz @ -10 dB, a gain of 5.7 dBi and a total efficiency of 88.4 % at 5.2 GHz, suitable for 5 G mobile communication systems.     

Experimental study on prediction model of wet gas pressure drop across single-orifice plate in horizontal pipes in the low gas phase Froude number region

The pressure drop prediction of wet gas across single-orifice plate in horizontal pipes had been solved satisfactorily under an annular-mist flow in the upstream of orifice plates. However, this pressure drop prediction is still not clearly determined when the upstream is in an intermittent flow or stratified flow, which is corresponding to a region of low Fr_G (gas phase Froude number) in the flow pattern map of wet gases. In this study, the wet gas pressure drop across a single-orifice plate was experimentally investigated in the low Fr_G region. By the experiment, the flow pattern transition in the downstream of single-orifice plates, as well as the effects of Fr_G and Fr_L (liquid phase Froude number) on Φ_G (gas phase multiplier), were determined and compared when the upstream is in the flow pattern transition and the stratified flow region, respectively. Prediction performances were examined on the available pressure drop models. It was found that no model could be capable of jointly predicting the wet gas pressure drop in the low Fr_G region with an acceptable accuracy. With a new method of correlating Fr_G and Fr_L simultaneously, new correlations were proposed for the low Fr_G region. Among which the modified Chisholm model shows the best prediction accuracies, with the prediction deviations of Φ_G being within 7% and 3% when the upstream is in flow pattern transition and stratified flow region, respectively.     

基于改进Faster R-CNN及YOLO的大角度车牌识别算法

随着大数据时代的到来,智慧城市等一系列概念的提出,人工智能开始在城市各个角落得到广泛应用。其中,车牌识别作为城市道路交通重要的一环,也取得了重大突破。基于深度学习的车牌识别一经提出,各类算法应用于车牌检测及识别上,对比于传统的车牌识别,大大提高了识别的速率和准确率。然而,在非限制条件下,如大角度车牌识别准确率仍有提升的空间。提出了一种改进的FasterR-CNN与YOLO的深度学习车牌识别算法,将对大角度下的车牌识别准确率达到了99.7%。由于是轻量型的框架,为后续的移动设备部署工作提供了便利。     

Synthesizing a uniformly spaced array pattern using integral operator for removing progressive phase shift

In this article, an analytical technique is introduced to obtain the excitation coefficients of uniformly spaced linear antenna arrays in order to achieve a desired array factor. By integration of the prescribed array factor, the array factor dependency to the progressive phase shift is eliminated. A new system of linear equations is consequently obtained whose solution represents the excitation coefficients of the array. Some examples are presented to verify the accuracy of the introduced method. The performance of this strategy is compared with those obtained by the other well‐known techniques such as Woodward‐Lawson and Fourier transform. It is shown that the presented method estimates the desired array pattern with a very good precision.     

Nature inspired 21 branches sneezewort/Achillea ptarmica plant growth pattern–shaped antenna for Ku‐band applications

This reported paper presents the design and analysis of wideband nature inspired planar antenna of 46 × 18 × 1.6 mm³ size, designed using FR4 (Flame Retardant) substrate. The antenna patch is delineated from the growth pattern of sneezewort plant with supplementary notion of golden ratio in branching and branch width. The total number of branches in each stage follows the Fibonacci series and the branch width is calculated from the golden ratio concept. Starting from one feed line and two branches, the maximum numbers of branches are increased to 20. There has been significant enhancement in the radiation performance of proposed geometry by increasing the number of branches to 21 and by modifying ground with T‐shaped slot. The antenna covers wide impedance bandwidth of 8.2 to 16.5 GHz by possessing stable radiation characteristics.     

ASME Ⅱ卷D篇表U数据作为设计校核中材料验收标准存在问题及探讨

ASME标准钢板对于短时高温抗拉数据无规定,但设备设计人员在校核时又要用到此数据,于是有些设计文件在技术要求中将ASME II卷表U的数据作为材料验收的标准。针对此种做法引发的争议及涉及的主要问题进行试验验证和分析探讨。研究结果表明,ASME II卷D篇表U中的数据是基于室温抗拉强度保证值,并根据拟合曲线将室温保证值提高了10%得到的,实测数据与ASME规范数据不一致,部分材料在250~350℃存在动态应变时效现象,但仍不满足设计要求。材料经模拟焊后热处理后性能下降,难以到达交货态的要求。给出了短时高温抗拉强度的选用建议。